ASTM A – Standard Specification for Annealed or Cold-Worked Austenitic Stainless Steel Sheet, Strip, Plate, and Flat Bar. This standard is a part of ASTM. ASTM A March 10, Standard Specification for Annealed or Cold- Worked Austenitic Stainless Steel Sheet, Strip, Plate, and Flat Bar. This specification. ASTM A – Designation: A – 10 Standard Speci?cation for Annealed or Cold-Worked Austenitic.

Author: Kakinos Yozshugal
Country: Cyprus
Language: English (Spanish)
Genre: Medical
Published (Last): 24 March 2010
Pages: 161
PDF File Size: 11.9 Mb
ePub File Size: 15.83 Mb
ISBN: 897-9-24452-624-8
Downloads: 26645
Price: Free* [*Free Regsitration Required]
Uploader: Akinotaxe

A number in parentheses indicates the year of last reapproval. If astn feel that your comments have not received a fair hearing you should make your views known to the ASTM Committee on Standards, at the address shown below. One bend test shall be made from one end of each coil.

These alloys represent an excellent combination of corrosion resistance and fabricability. Find out what NKS can do for you.

ASTM A for Annealed or Cold-Worked Austenitic Stainless Steel Sheet, Strip, Plate, and Flat Bar

A — 10 Standard Speci? Only annealed conditions of grades speci?

The values obtained in this manner should a666-1, however, be taken as the actual yield strength for 0. Type L should be used in heavier sections to reduce the occurrence of carbide precipitation in the heat affected region adjacent to the weld pool.

  DESCARGAR ARRANCAME LA VIDA-ANGELES MASTRETTA PDF

C Annealed material that naturally meets mechanical properties may be applied. Material Test Report and Certi? Maximum unless otherwise indicated. In case of dispute, qstm offset method of determining yield strength shall sstm used.

Type L LN Individual reprints single or multiple copies of this standard may be obtained by contacting ASTM at the above address or at phonefaxor service astm. This standard is subject to revision at any time by a66-10 responsible technical committee and must be reviewed every?

In the annealed condition it is essentially non-magnetic asttm becomes slightly magnetic with the application of cold work. Due to the high work hardening rate of these materials, intermediate anneals maybe required to successfully fabricate the part. This standard has been approved for use by agencies of the Department of Defense. Rockwell B 95 95 Originally approved in The noncontrolling factor normally will exceed considerably the speci?

Chemical equipment and piping, heat exchanger components, dairy and food handling equipment and utensils, cryogenic vessels and components, architectural and structural applications exposed to non-marine atmospheres.

Your comments are invited either for revision of this standard or for additional standards and should be addressed to ASTM International Headquarters. HRC typical L Ann 25 min. Depending on the work hardening characteristics of the particular grade, either the yield or the tensile strength can be the controlling factor in meeting the properties. Your comments will receive careful consideration at a meeting of the responsible technical committee, which you may attend.

  ALFRED RAPPAPORT CREATING SHAREHOLDER VALUE PDF

304 and 304L Stainless Steel

HardC Elongation in 2 in. Types and L cannot be hardened by thermal treatment. Users of this standard are expressly advised that a666–10 of atsm validity of any such patent rights, and the risk of infringement of such rights, are entirely their own responsibility. Number of Tests 8. Hard Elongation in 2 in. Type L should be used in heavier sections to reduce the occurrence of carbide precipitation in the heat affected region adjacent to the weld pool Corrosion: Chemical equipment and piping, heat exchanger components, dairy and food handling equipment and utensils, cryogenic vessels and components, architectural and structural applications exposed to non-marine atmospheres Chemical Composition: Types and L provides corrosion resistance in a wide range of moderately oxidizing and reducing conditions, fresh water and non-marine applications.

Permission rights to photocopy the standard may also be secured from the ASTM website www. Specimens shall be bent around a diameter equal to the product of the bend factor times the speci? The values given in parentheses are for information only.