ASTM A is the specification that covers the general requirements for flat- rolled stainless and heat-resisting steel plate, sheet and strip. It does not reference. 1 This specification is under the jurisdiction of ASTM Committee A01 on Steel, product specifications that reference Specification A/. ASTM A/AM Standard Specification for General Requirements for Flat -Rolled Stainless and Heat-Resisting Steel Plate, Sheet, and.
|Published (Last):||4 October 2009|
|PDF File Size:||9.74 Mb|
|ePub File Size:||3.90 Mb|
|Price:||Free* [*Free Regsitration Required]|
When intergranular corrosion tests are required, they shall be as agreed upon between the seller and the purchaser. Permitted Variations in Dimensions and Weight 9.
When awtm corrosion is of concern, the purchaser should specify the corrosion test of One surface, to be the outside surface in bending, a408 be the original surface of the plate; however, surface preparation by light grinding is permitted.
All austenitic chromium-nickel types except the H types are expected to be capable of passing this test. Combining values from the two systems may result in nonconformance with the specification.
D Quenched in water, except that coiled product heat treated in a continuous annealing line shall be water quenched or rapidly cooled by other means. Special tests like intergranular corrosion test, permeability test, Charpy impact testing and tests for detrimental intermetallic phases in wrought asttm stainless steels shall be also be performed when required.
For the purposes of this speci? Typically, very faint buff of asrm lines may still be visible on the? It is produced by buffing a? Architectural Finishes—Sometimes described as a No.
ASTM A480 Plate Thickness & Flatness Tolerances
In the case of transverse zstm test specimens, the axis of bend shall be parallel to the direction of rolling. Packaging, Marking, and Loading Use of plates in this condition is generally con?
NOTE 2—The tolerances in this table include crown tolerances. The gage number shall not be a basis for rejection.
Finish for Strip The use of the gage number is discouraged as being an archaic term of limited usefulness not having general agreement on meaning. When polished on one side only, it is permitted to rough grind the other zstm in order to obtain the necessary? B Maximum deviation from a horizontal?
ASTM A Specification | Penn Stainless Products
NOTE 3—For plates with speci? This analysis shall be made from a test sample taken during the pouring of the melt, or from the in-process product later in the manufacturing? This standard is subject to revision at any time by the responsible technical committee and must be reviewed every?
NOTE 2—Cold-rolled sheets in cut lengths and coils are produced in some type numbers and some widths and thickness to tolerances less than those shown in the table. NOTE 2—Notwithstanding the absence of a signature, the organization submitting the report is responsible for the content of the report.
Approved April 1, The allowable variation of a particular element in a single sample for product analysis is permitted to be either above or below the speci? NOTE 2—If the longer dimension is under 36 in. Users of this standard are expressly advised that determination of the validity of any such patent rights, and the risk of infringement of such rights, are entirely their own responsibility.
Test data from a minimum of three test lots, as de? However, percentages must exhibit the same tendencies in all samples; that is, the several determinations of any individual element in a heat shall not vary both above and below the speci?
ASTM Specification A – What is it? – NKS
Requirements for AM are given in Annex A3. Within the text, the SI units are shown in brackets, except that when AM is speci?
In the case of con? Link to Active This link will always route to the current Active version of the standard.
Approved November 15, For narrow strip, the following widths can be tested: The purchase order requirements shall not take precedence if they, in any way, violate the requirements of the product speci?
The applicable levels shall be as speci? The applicability of these tests to duplex stainless steels not listed in Test Methods A shall be a matter for negotiation between the seller and the purchaser.
ASTM A480 Specification
Such analysis shall be made by any of the commonly accepted methods that will positively identify the material. Heat treatment thermal cycles shall be separate from other thermal processing cycles; for example, in-process thermal cycles are not permitted as a substitute for the separate annealing cycle.
The manufacturer is permitted, if necessary, use a lower temperature resolution anneal or a stabilization anneal after a high temperature solution anneal in order to meet corrosion test requirements.